Register a snapshot repositoryedit

This guide shows you how to register a snapshot repository. A snapshot repository is an off-cluster storage location for your snapshots. You must register a repository before you can take or restore snapshots.

In this guide, you’ll learn how to:

  • Register a snapshot repository
  • Verify that a repository is functional
  • Clean up a repository to remove unneeded files

Prerequisitesedit

  • To use Kibana’s Snapshot and Restore feature, you must have the following permissions:

  • To register a snapshot repository, the cluster’s global metadata must be writeable. Ensure there aren’t any cluster blocks that prevent write access.

Considerationsedit

When registering a snapshot repository, keep the following in mind:

  • Each snapshot repository is separate and independent. Elasticsearch doesn’t share data between repositories.
  • Clusters should only register a particular snapshot repository bucket once. If you register the same snapshot repository with multiple clusters, only one cluster should have write access to the repository. On other clusters, register the repository as read-only.

    This prevents multiple clusters from writing to the repository at the same time and corrupting the repository’s contents. It also prevents Elasticsearch from caching the repository’s contents, which means that changes made by other clusters will become visible straight away.

  • When upgrading Elasticsearch to a newer version you can continue to use the same repository you were using before the upgrade. If the repository is accessed by multiple clusters, they should all have the same version. Once a repository has been modified by a particular version of Elasticsearch, it may not work correctly when accessed by older versions. However, you will be able to recover from a failed upgrade by restoring a snapshot taken before the upgrade into a cluster running the pre-upgrade version, even if you have taken more snapshots during or after the upgrade.

Manage snapshot repositoriesedit

You can register and manage snapshot repositories in two ways:

To manage repositories in Kibana, go to the main menu and click Stack Management > Snapshot and Restore > Repositories. To register a snapshot repository, click Register repository.

You can also register a repository using the Create snapshot repository API.

Snapshot repository typesedit

Supported snapshot repository types vary based on your deployment type:

Elasticsearch Service repository typesedit

Elasticsearch Service deployments automatically register the found-snapshots repository. Elasticsearch Service uses this repository and the cloud-snapshot-policy to take periodic snapshots of your cluster. You can also use the found-snapshots repository for your own SLM policies or to store searchable snapshots.

The found-snapshots repository is specific to each deployment. However, you can restore snapshots from another deployment’s found-snapshots repository if the deployments are under the same account and in the same region. See the Cloud Snapshot and restore documentation to learn more.

Elasticsearch Service deployments also support the following repository types:

Self-managed repository typesedit

If you manage your own Elasticsearch cluster, you can use the following built-in snapshot repository types:

Other repository types are available through official plugins:

You can also use alternative storage implementations with these repository types, as long as the alternative implementation is fully compatible. For instance, MinIO provides an alternative implementation of the AWS S3 API and you can use MinIO with the s3 repository type.

Note that some storage systems claim to be compatible with these repository types without emulating their behaviour in full. Elasticsearch requires full compatibility. In particular the alternative implementation must support the same set of API endpoints, return the same errors in case of failures, and offer equivalent consistency guarantees and performance even when accessed concurrently by multiple nodes. Incompatible error codes, consistency or performance may be particularly hard to track down since errors, consistency failures, and performance issues are usually rare and hard to reproduce.

You can perform some basic checks of the suitability of your storage system using the Repository analysis API. If this API does not complete successfully, or indicates poor performance, then your storage system is not fully compatible and is therefore unsuitable for use as a snapshot repository. You will need to work with the supplier of your storage system to address any incompatibilities you encounter.

Verify a repositoryedit

When you register a snapshot repository, Elasticsearch automatically verifies that the repository is available and functional on all master and data nodes.

To disable this verification, set the create snapshot repository API's verify query parameter to false. You can’t disable repository verification in Kibana.

PUT _snapshot/my_unverified_backup?verify=false
{
  "type": "fs",
  "settings": {
    "location": "my_unverified_backup_location"
  }
}

If wanted, you can manually run the repository verification check. To verify a repository in Kibana, go to the Repositories list page and click the name of a repository. Then click Verify repository. You can also use the verify snapshot repository API.

POST _snapshot/my_unverified_backup/_verify

If successful, the request returns a list of nodes used to verify the repository. If verification fails, the request returns an error.

You can test a repository more thoroughly using the repository analysis API.

Clean up a repositoryedit

Repositories can over time accumulate data that is not referenced by any existing snapshot. This is a result of the data safety guarantees the snapshot functionality provides in failure scenarios during snapshot creation and the decentralized nature of the snapshot creation process. This unreferenced data does in no way negatively impact the performance or safety of a snapshot repository but leads to higher than necessary storage use. To remove this unreferenced data, you can run a cleanup operation on the repository. This will trigger a complete accounting of the repository’s contents and delete any unreferenced data.

To run the repository cleanup operation in Kibana, go to the Repositories list page and click the name of a repository. Then click Clean up repository.

You can also use the clean up snapshot repository API.

POST _snapshot/my_repository/_cleanup

The API returns:

{
  "results": {
    "deleted_bytes": 20,
    "deleted_blobs": 5
  }
}

Depending on the concrete repository implementation the numbers shown for bytes free as well as the number of blobs removed will either be an approximation or an exact result. Any non-zero value for the number of blobs removed implies that unreferenced blobs were found and subsequently cleaned up.

Please note that most of the cleanup operations executed by this endpoint are automatically executed when deleting any snapshot from a repository. If you regularly delete snapshots, you will in most cases not get any or only minor space savings from using this functionality and should lower your frequency of invoking it accordingly.

Back up a repositoryedit

You may wish to make an independent backup of your repository, for instance so that you have an archive copy of its contents that you can use to recreate the repository in its current state at a later date.

You must ensure that Elasticsearch does not write to the repository while you are taking the backup of its contents. You can do this by unregistering it, or registering it with readonly: true, on all your clusters. If Elasticsearch writes any data to the repository during the backup then the contents of the backup may not be consistent and it may not be possible to recover any data from it in future.

Alternatively, if your repository supports it, you may take an atomic snapshot of the underlying filesystem and then take a backup of this filesystem snapshot. It is very important that the filesystem snapshot is taken atomically.

You cannot use filesystem snapshots of individual nodes as a backup mechanism. You must use the Elasticsearch snapshot and restore feature to copy the cluster contents to a separate repository. Then, if desired, you can take a filesystem snapshot of this repository.

When restoring a repository from a backup, you must not register the repository with Elasticsearch until the repository contents are fully restored. If you alter the contents of a repository while it is registered with Elasticsearch then the repository may become unreadable or may silently lose some of its contents.